Safety Data Sheets / Polymount Kit - Component B

Safety Data Sheet

Polymount Kit - Component B

Version 1Last reviewed 27 February 2026Catalogue: 1270B, EMS1270

1. Identification

Product Identifiers

Product Name: Polymount Kit - Component A
Other Names: Polymount Embedding Hardener
Product Number(s): 1270B, EMS1270
CAS Number: Not available.

Recommended use of the chemical and restriction on use

Laboratory chemicals.

Company Details

ProSciTech Pty Ltd
11 Carlton Street
KIRWAN QLD 4817
Australia
(07) 4773 9444
pst@proscitech.com
proscitech.com.au

Emergency Contact Details

ProSciTech Pty Ltd
11 Carlton Street
KIRWAN QLD 4817
Australia
(07) 4773 9444
pst@proscitech.com
proscitech.com.au

2. Hazards Identification

Classification of the substance or mixture

Classification according to Directive 67/548/EEC or Directive 1999/45/EC
Harmful
Harmful by inhalation, in contact with skin and if swallowed.
Flammable

Label Elements

Signal Words: None
Hazard Statement(s): Hazard-determining components of labelling: 2-Butane, peroxide.
Flamma.
Harmful by inhalation, in contact with skin and if swallowed.
Precautionary Statement(s): Keep container in well-ventilated place.
Keep away from heat.
Wear suitable protective clothing and gloves.
This material and its container must be disposed of as hazardous waste.

Primary route(s) of entry

Not available.

Human Health

Inhalation: Harmful by inhalation.
Ingestion: Harmful if swallowed.
Eyes: No further relevant information available.
Skin: Wear suitable protective clothing and gloves.

Environment

This material and its container must be disposed of as hazardous waste.

3. Composition / Information on Ingredients

Name	CAS No.	Content (w/w)	Classification
dimethyl phthalate	131-11-3	50-100%	Not Available
2-Butanone, peroxide	1338-23-4	25-50%	Not Available
METHYL ETHYL KETONE	78-93-3	2.5-10%	Not Available

4. First Aid Measures

Ingestion: Call for a doctor immediately.
Inhalation: Supply fresh air. If required, provide artificial respiration. Keep patient warm. Consult doctor if symptoms persist.
In case of unconsciousness place patient stably in side position for transportation.
Skin Contact: Generally the product does not irritate the skin.
Eye Contact: Rinse opened eye for several minutes under running water.
Other Information: Symptoms of poisoning may even occur after several hours; therefore medical observation for at least 48 hours after the accident.

5. Firefighting Measures

Suitable extinguishing equipment

Fire: CO₂, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
HAZCHEM: No further relevant information available

Special protective equipment and precautions for fire fighters

Mouth respiratory protective device.

6. Accidental Release Measures

Personal precautions, protective equipment and emergency procedures: Wear protective equipment. Keep unprotected persons away.
Environmental precautions: Dilute with plenty of water.
Do not allow to enter sewers/surface or ground water.
Methods and materials for containment and clean up: Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).
Dispose contaminated material as waste according to item 13.
Ensure adequate ventilation.

7. Handling and Storage

Precautions for safe handling: Ensure good ventilation/exhaustion at the workplace.
Prevent formation of aerosols.
Keep ignition sources away - Do not smoke.
Protect from heat.
Protect against electrostatic charges.
Conditions for safe storage: Keep container tightly sealed.
Protect from heat and direct sunlight.

8. Exposure Controls / Personal Protection

Exposure Standards

Material	TWA ppm	TWA mg/m³	STEL ppm	STEL mg/m³
131-11-3 dimethyl phthalate		5mg/m³
1338-23-4 2-Butanone, peroxide	Peak limitation 0.2ppm	Peak limitation 1.5mg/m³
78-93-3 METHYL ETHYL KETONE	150ppm	445mg/m³	300ppm	890mg/m³

Engineering controls: Keep away from foodstuffs, beverages and feed.
Wash hands before breaks and at the end of work.
Avoid contact with the eyes and skin.

Personal protective equipment

Eye and face protection: Tightly sealed goggles.
Skin protection: Protective gloves. The glove material has to be impermeable and resistant to the product/the substance/the preparation. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation. The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Body protection: Protective clothing.
Respiratory protection: In case of brief exposure of low pollution use respiratory filter device. In case of intensive or longer exposure use self-contained respiratory protective device.

9. Physical and Chemical Properties

General information

Appearance: Yellow liquid
Odour: Characteristic.
pH: Not determined
Vapour Pressure: Not determined
Density: 1.14736g/cm³
Boiling Point: 81°C
Melting Point: Undetermined
Solubility: Fully miscible
Specific Gravity of Density: Not available
Flash Point: 34°C
Flammable (Explosive) Limits: Not determined.
Ignition Temperature: 555°C
Formula: Not available

10. Stability and Reactivity

Reactivity: No further relevant information available.
Chemical stability: No decomposition if used according to specifications.
Possibility of hazardous reactions: No dangerous reactions known.
Conditions to avoid: No further relevant information available.
Incompatible materials: No further relevant information available.

11. Toxicological Information

Acute effects: No further relevant information available.
Eye contact: No irritating effect.
Skin contact: No irritant effect.
Ingestion: No further relevant information available.
Inhalation: No sensitising effects known.
Toxicity and irritation: Harmful

12. Ecological Information

Ecotoxicity: No further relevant information available.
Persistence and degradability: No further relevant information available.
Bioaccumulative potential: No further relevant information available.
Other adverse effects: Water hazard class 1: slightly hazardous for water.
Do not allow undiluted product or large quantities of it to reach ground eater, water course or sewage system.

13. Disposal Considerations

General information

Must not be disposed of together with household garbage. Do not allow product to reach sewage system.
Disposal must be made according to official regulations.
Recommended cleansing agents: Water, if necessary together with cleansing agents.

14. Transport Information

ADG label required

HAZCHEM: No further relevant information available
UN Number: UN1866
Proper shipping name: 1866 RESIN SOLUTION
Transport hazard class: Class 3 Flammable liquids
Packing group: III
Environmental hazard: No
Special precautions for users: Warning: Flammable liquids.
Additional information: Limited quantities (LQ) 5L
Excepted quantities (EQ) Code: E1
Maximum net quantity per inner packaging: 30mL
Maximum net quantity per outer packaging: 1000ml

15. Regulatory Information

Poisons Schedule Number: 78-93-3 METHYL ETHYL KETONE S5
Other Information: A Chemical Safety Assessment has not been carried out.

16. Other Information

SDS preparation date: 27 February 2026
Comments: This information is based on our present knowledge. However, this shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship.