PELCO Pro CA44 Tissue Adhesive

1. Identification

Product Identifiers

Product Name

PELCO Pro CA44 Tissue Adhesive

Other Names

Super Glue, Instant Adhesive, Cyanoacrylate

Product Number(s)

10033, 14460, 14464, 14465, 14470, 14474, 14477, 14478 PELCO PRO CA44, C100, C1000. CA-GEL CYANOACRYLATE GLUE, C300, C5, PEL10033

CAS Number

Not available

Recommended use of the chemical and restriction on use

Company Details

Emergency Contact Details

2. Hazards Identification

Classification of the substance or mixture

Label Elements

Signal Words

Warning

Hazard Statement(s)

• H319 Causes serious eye irritation.
• H335 May cause respiratory irritation.
• H315 Causes skin irritation.
• EUH202 "Cyanoacrylate. Danger. Bonds skin and eyes in seconds. Keep out of reach of children."

Precautionary Statement(s)

• P280 Wear protective gloves/protective clothing/eye protection/face protection.
• P340±340 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
• P332±313 If skin irritation occurs: Get medical advice/attention.
• P305±351±338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P403±233 Store in a well-ventilated place. Keep container tightly closed.
• P501 Dispose of contents/container as hazardous or special waste.

Primary route(s) of entry

Human Health

Inhalation

No further information available.

Ingestion

No further relevant information available.

Eyes

No further relevant information available.

Skin

No further relevant information available.

Environment

3. Composition / Information on Ingredients

4. First Aid Measures

Ingestion

Ensure that breathing passages are not obstructed. The product will polymerise immediately in the mouth making it almost impossible to swallow. Saliva will slowly separate the solidified product from the mouth (several hours).

Inhalation

IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. If still feeling unwell seek medical attention.

Skin Contact

IF ON SKIN: Wash with plenty of soap and water. Do not pull bonded skin apart. It may be gently peeled apart using a blunt object such as a spoon, preferably after soaking in warm soapy water. Cyanoacrylates give off heat on solidification. In rare cases a large drop will generate enough heat to cause a burn. Burns should be treated normally after the adhesive has been removed from the skin. If lips are accidentally stuck together apply warm water to the lips and encourage maximum wetting and pressure from saliva inside the mouth. Peel or roll lips apart. Do not try to pull the lips apart with direct opposing action. If skin irritation occurs: Get medical advice/attention.

Eye Contact

IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If the eye is bonded closed, release eyelashes with warm water by covering with wet pad. Cyanoacrylate will bond to eye protein and will cause periods of weeping which will help to debond the adhesive. Keep eye covered until debonding is complete, usually within 1-3 days. Medical advice should be sought in case solid particles of cyanoacrylate trapped behind the eyelid cause any abrasive damage.

Other Information

Call a POISON CENTER or doctor/physician if you feel unwell.

5. Firefighting Measures

Suitable extinguishing equipment

Fire

• Dry powder, foam, carbon dioxide, fine water spray.
• Unsuitable extinguishing agents: water jet.

HAZCHEM

• Trace amounts of toxic fumes may be release on incineration.
• Hazardous combustion products: oxides of carbon, oxides of nitrogen, irritating organic vapours.

Special protective equipment and precautions for fire fighters

6. Accidental Release Measures

Personal precautions, protective equipment and emergency procedures

Ensure adequate ventilation. Wear protective gloves/protective clothing/eye protection/face protection. Avoid skin and eye contact. Avoid breathing dust/fume/gas/mist/vapours/spray.

Environmental precautions

Do not let product enter drains.

Methods and materials for containment and clean up

• Do not use clothes for mopping up. Flood with water to complete polymerisation and scrape off the floor. Cured material can be disposed of as non-hazardous waste.
• Dispose of waste according to Federal, State and Local Regulations.

7. Handling and Storage

Precautions for safe handling

Avoid breathing dust/fume/gas/mist/vapours/spray. Use only outdoors or in a well-ventilated area. Ventilation (low level) is recommended when using large volumes. Use of dispensing equipment is recommended to minimize risk of skin or eye contact. Wash hands thoroughly after handling.

Conditions for safe storage

For optimum shelf life store in original containers under refrigerated conditions at 2 DegC to 8 DegC. Store locked up.

8. Exposure Controls / Personal Protection

Exposure Standards

Engineering controls

Provide adequate ventilation in area of use. Do NOT use this product in an enclosed or poorly ventilated area. Local exhaust ventilation is normally required when handling or using this product to keep airborne powder below the nationally authorised limits. If ventilation alone cannot control exposure, respiratory protection must be worn.

Personal protective equipment

Eye and face protection

Wear protective glasses.

Skin protection

Protective gloves: in circumstances where there is potential for prolonged or repeated skin contact, the use of polyvinyl chloride or nitrile rubber gauntlets or equivalent solvent resistant gloves is recommended. The use of chemical resistant gloves such as Nitrile is recommended. Polyethylene or polypropylene gloves are recommended when using large volumes. Do Not use PVC, rubber or nylon or cotton gloves.

Body protection

Good industrial hygiene practices should be observed. Take off contaminated clothing and wash it before reuse. Wash hands thoroughly after handling.

Respiratory protection

Ensure adequate ventilation.

9. Physical and Chemical Properties

General information

Appearance

Transparent, colourless liquid

Odour

Pungent

pH

Not determined

Vapour Pressure

<21Pa

Density

Not determined

Boiling Point

214°C

Melting Point

-31°C

Solubility

<0.024 mg/l

Specific Gravity of Density

1.043 b/cm³ at 20°C

Flash Point

82.5°C

Flammable (Explosive) Limits

Not determined

Ignition Temperature

480°C

Formula

Not available

10. Stability and Reactivity

Reactivity

No further information available.

Chemical stability

Stable under normal conditions of storage and use.

Possibility of hazardous reactions

• Hazardous Decomposition Products: Oxides of carbon, oxides of nitrogen.
• Hazardous Polymerization: Will not occur.

Conditions to avoid

Moisture, humidity, basic material.

Incompatible materials

Water, soil, amines, alkalis, and alcohols.

11. Toxicological Information

Acute effects

• Oral: LD50 (oral, rat) >5000 mg/kg bw (OECD 401)
• Dermal: LD50 (dermal, rabbit) >2000 mg/kg bw (OECD 402)
• Inhalation: In dry atmosphere with <50% humidity, vapours may irritate the eyes and respiratory system.
• Prolonged exposure to high concentration of vapours may lead to chronic effects in sensitive individuals.

Eye contact

Irritating to eyes. In dry atmosphere (RH<50%) vapours may cause irritation and lachrymatory effect.

Skin contact

Causes skin irritation.

Ingestion

No further information available.

Inhalation

Due to polymerization at the skin surface allergic reaction is not considered possible. The polymerised material is not able to penetrate into the epidermis.

Toxicity and irritation

No further information available.

12. Ecological Information

Ecotoxicity

Low ecotoxicity.

Persistence and degradability

NA (the test compound would polymerise with contact of water or the moisture of the soil immediately).

Bioaccumulative potential

NA (in presence of moisture ethyl-2-cyanoacrylate polymerises within seconds).

Other adverse effects

No further relevant information available.

13. Disposal Considerations

General information

14. Transport Information

ADG label required

HAZCHEM

• Trace amounts of toxic fumes may be release on incineration.
• Hazardous combustion products: oxides of carbon, oxides of nitrogen, irritating organic vapours.

UN Number

No further information available

Proper shipping name

Unrestricted, combustible liquid

Transport hazard class

No further information available.

Packing group

No further information available.

Environmental hazard

No

Special precautions for users

No further information available.

Additional information

No further information available.

15. Regulatory Information

Poisons Schedule Number

Not determined.

Other Information

No further relevant information available.

16. Other Information

SDS preparation date

26 February 2026

Comments

This information is based on our present knowledge. However, this shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship.