Mobil DTE Vacuum Pump Oil, Medium

1. Identification

Product Identifiers

Product Name

Mobil DTE Vacuum Pump Oil, Medium

Other Names

DTE Oil Medium

Product Number(s)

M007

CAS Number

?

Recommended use of the chemical and restriction on use

Company Details

Emergency Contact Details

2. Hazards Identification

Classification of the substance or mixture

Label Elements

Signal Words

Danger

Hazard Statement(s)

NON-HAZARDOUS SUBSTANCE. NON-DANGEROUS GOODS.

Precautionary Statement(s)

Not applicable.

Primary route(s) of entry

Human Health

Inhalation

Not available.

Ingestion

Not available.

Eyes

Not available.

Skin

Not available.

Environment

3. Composition / Information on Ingredients

No information provided.

4. First Aid Measures

Ingestion

First aid is normally not required. Seek medical attention if discomfort occurs.

Inhalation

Remove from further exposure. For those providing assistance, avoid exposure to yourself or others. Use adequate respiratory protection. If respiratory irritation, dizziness, nausea, or unconsciousness occurs, seek immediate medical assistance. If breathing has stopped, assist ventilation with a mechanical device or use mouth-to-mouth resuscitation.

Skin Contact

Wash contact areas with soap and water. If product is injected into or under the skin, or into any part of the body, regardless of the appearance of the wound or its size, the individual should be evaluated immediately by a physician as a surgical emergency. Even though initial symptoms from high pressure injection may be minimal or absent, early surgical treatment within the first few hours may significantly reduce the ultimate extent of injury.

Eye Contact

Flush thoroughly with water. If irritation occurs, get medical assistance.

Other Information

No further relevant information available.

5. Firefighting Measures

Suitable extinguishing equipment

Fire

Use water fog, foam, dry chemical or carbon dioxide (CO₂) to extinguish flames. DO NOT USE straight streams of water.

Large Fire

Use water fog, foam, dry chemical or carbon dioxide (CO₂) to extinguish flames. DO NOT USE straight streams of water.

HAZCHEM

Not available.

Special protective equipment and precautions for fire fighters

6. Accidental Release Measures

Personal precautions, protective equipment and emergency procedures

Avoid contact with spilled material. See Section 5 for firo fighting information. See the Hazard Identification Section for Significant Hazards. See Section 4 for First Aid Advice. See Section 8 for advice on the minimum requirements for personal protective equipment. Additional protective measures may be necessary, depending on the specific circumstances and/or the export judgment of the emergency responders. For emergency responders: Respiratory protection: respiratory protection will be necessary only In special cases, e.g., formation of mists. Half-face or full-face respirator with filter(s) for dust/organic vapour or Self Contained Breathing Apparatus (SCBA) can be used depending on the size of spill and potential level of exposure. If the exposure cannot be completely characterised or an oxygen deficient atmosphere Is possible or anticipated, SCBA Is recommended. Work gloves that are resistant to hydrocarbons are recommended. Gloves made of polyvinyl acetate (PVA) arc not water-resistant and are not suitable for emergency use. Chemical goggles are recommended if splashes or contact with eyes is possible. Small spills: normal antistatic work clothes are usually adequate. Large spills: full body suit of chemical resistant, antistatic material is recommended.

Environmental precautions

Large Spills: Dyke far ahead of liquid spill for later recovery and disposal. Prevent entry into waterways, sewers, basements or confined areas.

Methods and materials for containment and clean up

• Notify relevant authorities in accordance with all applicable regulations.Land Spill: Stop leak if you can do so without risk. Recover by pumping or with suitable absorbent.
• Water Spill: Stop leak if you can do so without risk. Confine the spill immediately with booms. Warn other shipping. Remove from the surface by skimming or with suitable absorbents. Seek the advice of a specialist before using dispersants. Water spill and land spill recommendations are based on the most likely spill scenario for this material; however, geographic conditions, wind, temperature, (and in the case of a water spill) wave and current direction and speed may greatly influence the appropriate action to be taken. For this reason, local experts should be consulted. Note: Local regulations may prescribe or limit action to be taken.

7. Handling and Storage

Precautions for safe handling

• Prevent small spills and leakage to avoid slip hazard. This material is a static accumulator.
• Material can accumulate static charges which may cause an electrical spark (ignition source). When the material is handled in bulk, an electrical spark could ignite any flammable vapours from liquids or residues that may be present (e.g., during switch-loading operations). Use proper bonding and/or ground procedures. However, bonding and grounds may not eliminate the hazard from static accumulation. Consult local applicable standards for guidance.

Conditions for safe storage

• The container choice, for example storage vessel, may effect static accumulation and dissipation In open or unlabelled containers. Keep away from incompatible materials.
• Do not store in open or unlabelled containers.

8. Exposure Controls / Personal Protection

Exposure Standards

Engineering controls

The level of protection and types of controls necessary will vary depending upon potential exposure conditions.Control measures to consider: No special requirements under ordinary conditions of use and with adequate ventilation.

Personal protective equipment

Eye and face protection

If contact is likely, safety glasses with side shields are recommended.

Skin protection

• Any specific glove information provided is based on published literature and glove manufacturer data. Glove suitability and breakthrough time will differ depending on the specific use conditions. Contact the glove manufacturer for specific advice on glove selection and breakthrough times for your use conditions. Inspect and replace worn or damaged gloves. The types of gloves to be considered for this material include: Nitrile, Viton.
• No protection is ordinarily required under normal conditions of use.Any specific clothing information provided is based on published literature or manufacturer data. The types of clothing to be considered for this material include:
• No skin protection is ordinarily required under normal conditions of use. In accordance with good industrial hygiene practices, precautions should be taken to avoid skin contact.

Body protection

Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. Discard contaminated clothing and footwear that cannot be cleaned. Practice good housekeeping.Personal protective equipment selections vary based on potential exposure conditions such as applications, handling practices, concentration and ventilation. Information on the selection of protective equipment for use with this material, is based upon intended, normal usage.

Respiratory protection

• If engineering controls do not maintain airborne contaminant concentrations at a level which is adequate to protect worker health, an approved respirator may be appropriate. Respirator selection, use, and maintenance must be in accordance with regulatory requirements, if applicable.Types of respirators to be considered for this material include:
• Particulate: No special requirements under ordinary conditions of use and with adequate ventilation.
• For high airborne concentrations, use an approved supplied-air respirator, operated in positive pressure mode. Supplied air respirators with an escape bottle may be appropriate when oxygen levels are inadequate, gas/vapour warning properties are poor, or if air purifying filter capacity/rating may be exceeded.

9. Physical and Chemical Properties

General information

Appearance

Amber liquid.

Odour

Characteristic.

pH

Not available.

Vapour Pressure

< 0.013 kPa (0.1 mm Hg) at 20°C

Density

(Air = 1): > 2 at 101 kPa

Boiling Point

> 316°C

Melting Point

Not available.

Solubility

Negligible solubility in water.

Specific Gravity of Density

Relative density at 15°C: 0.87

Flash Point

>200°C.

Flammable (Explosive) Limits

LEL: 0.9 UEL: 7.0

Ignition Temperature

Not available.

Formula

Not available.

10. Stability and Reactivity

Reactivity

No further relevant information available.

Chemical stability

Stable under normal conditions of use. Material does not decompose at ambient temperatures.

Possibility of hazardous reactions

Will not occur.

Conditions to avoid

Excessive heat. High energy sources of ignition and incompatible materials.

Incompatible materials

Strong oxidisers.

11. Toxicological Information

Acute effects

No further relevant information available.

Eye contact

• Excessive exposure may result in eye irritation.
• Irritation (Rabbit): Data available. May cause mild, short-lasting discomfort to eyes. Based on test data for structurally similar materials

Skin contact

• Excessive exposure may result in skin irritation; high-pressure injection under skin may cause serious damage.Toxicity (Rabbit): LD50 > 5000 mg/kg
• Minimally Toxic. Based on test data for structurally similar materials.
• Irritation (Rabbit): Data available. Negligible irritation to skin at ambient temperatures. Based on test data for structurally similar materials.

Ingestion

• Low order of toxicity ? effects unknown.Toxicity (Rat): LD50 > 5000 mg/kg
• Minimally Toxic. Based on test data for structurally similar materials

Inhalation

• Excessive exposure may result in respiratory irritation.
• Toxicity (Rat): LC50 > 5000 mg/m³
• Minimally Toxic. Based on test data for structurally similar materials.
• Irritation: No end point data. Negligible hazard at ambient/normal handling temperatures. Based on assessment of the components.

Toxicity and irritation

No further relevant information available.

12. Ecological Information

Ecotoxicity

Not expected to be harmful to aquatic organisms.

Persistence and degradability

Base oil component ? Expected to be inherently biodegradable

Bioaccumulative potential

Has the potential to bioaccumulate, however metabolism or physical properties may reduce the bioconcentration or limit bioavailability.

Other adverse effects

Base oil component ? Low solubility and floats and is expected to migrate from water to the land. Expected to partition to sediment and wastewater solids.

13. Disposal Considerations

General information

14. Transport Information

ADG label required

HAZCHEM

Not available.

UN Number

None.

Proper shipping name

Not regulated.

Transport hazard class

0

Packing group

None.

Environmental hazard

Not regulated.

Special precautions for users

Not regulated.

Additional information

Not regulated.

15. Regulatory Information

Poisons Schedule Number

Not regulated.

Other Information

No further information available.

16. Other Information

SDS preparation date

25 February 2026

Comments

This information is based on our present knowledge. However, this shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship.

References

• List of Publications referenced when creating this MSDS;
• Hazardous Substances Information System Consolidated Lists: Safe Work Australia.
• APPROVED CRITERIA FOR CLASSIFYING HAZARDOUS SUBSTANCES [NOHSC:1008(2004)] 3rd Edition: National Occupational Health and Safety Commission.
• Dangerous Goods ? Initial Emergency Response Guide (SAA/SNZ HB76:1997).
• IATA Dangerous Goods Regulations.
• Adopted National Exposure Standards for Atmospheric Contaminants in the Occupational Environment [NOHSC:1003(1995)].
• Australia Standard for the Uniform Scheduling of Drugs and Poisons [SUSPD] (Australian Government Department of Health and Ageing).